rust-stm32f1xx-hal-zrymod-20210426/CHANGELOG.md

Change Log

All notable changes to this project will be documented in this file.

The format is based on Keep a Changelog and this project adheres to Semantic Versioning.

Unreleased

Breaking changes

• Bump stm32f1 dependency (0.11.0)
• Make traits rcc::Enable and rcc::Reset public, but RccBus sealed

Added

• Extend the Pwm implementation to cover the full embedded_hal::Pwm API
• Add QeiOptions struct to configure slave mode and auto reload value of QEI interface
• Implement multiplication and division for frequency wrappers (#193)

Changed

• Support for connectivity line devices: stm32f105xx and stm32f107xx
• Consistently use PAC as pac and mark device and stm32 informally as deprecated
• Replace default blocking spi Write implementation with an optimized one
• Use Deref for SPI generic implementations instead of macros

Fixed

• Fix PWM on TIM1
• Fix ADC race condition causing incorrect reads at certain frequencies

v0.5.3 - 2020-01-20

• Add InputPin impl for generic open drain outputs
• Implement Read<u8> / Write<u8> for Serial (#171)
• Fix docs.rs build

v0.5.2 - 2019-12-15

• Fix USB module docs

v0.5.1 - 2019-12-14

Added

• Added support for ExtiPin pin traits

Fixed

• Fix SPI2 and 3 using the wrong frequency
• Fix some problems with I2C reads anad writes

v0.5.0 - 2019-12-03

Added

• Added Mode marker trait for gpio pins that correspondent to pin mode.
• RCC Bus trait + private Enable and Reset traits
• Added micros_since and reset methods to timer
• Added select_frequency method to RTC
• Unidirectional DMA support for SPI (TX only)
• Added USB driver for stm32f102 and stm32f103 devices
• Added all timers for all variants as described by CubeMX. Commented out {TIM9, TIM10} for XL and {TIM12, TIM13, TIM14} for XL and F100-HIGH due to missing fields for those devices in stm32-rs.
• ADC measurement now can be run by timer

Breaking changes

• Implement more pin combinations for PWM configuration, added PWM for TIM1 (API for custom PWM pins was removed as it's no more needed)
• Bump stm32f1 dependency (0.9.0)
• void::Void replaced with Infallible where it is possible
• Change timer/pwm init API
• Remove set_low and set_high for pins in Alternate output mode
• Renames set_seconds and seconds methods on RTC to set_time and current_time, respectively
• Starting the timer does not generate interrupt requests anymore
• Make MAPR::mapr() private
• i2c mode now takes Hertz instead of a generic u32
• Timers that were previously incorrectly available without medium/high/xl density features may now be missing

Fixed

• Fix some F1 variants crashing when modifying MAPR if JTAG is disabled
• Switched Timer stop_in_debug to modify cr instead of writing it to prevent it clobbering the rest of the register (was breaking ITM output when configuring pwm_input for example)

Changed

• Pins can be passed in any order to SPI constructor, NoSck, NoMiso and NoMosi can be also passed instead of real pin
• DMA traits now require AsSlice instead of AsRef

• GPIO downgrade function now returns a Pxx instead of a type specific to a GPIO port

• AdcDma can process several pins at a time

v0.4.0 - 2019-08-09

Added

• Added DMA support for ADC1.
• Added type aliases Tx1 for Tx<USART1>, RxDma1 for RxDma<USART1, dma1::C5>, etc.
• Add ADC1 reading functions for channels 16 (temperature) and 17 (internal reference voltage)
• Update existing ADC example according to ADC API changes
• Add new ADC example to read ambient temperature using ADC1 CH16
• Add listen and unlisten to serial::Tx and serial::Rx.
• Add methods read_data_register and write_data_register to backup_domain::BackupDomain, which allow read and write access to the Backup Data Register.

Breaking changes

• Replace gpio traits with digital::v2
• Bump stm32f1 dependency (0.8.0)
• ADC now requires the clock configuration for initialisation
• disable_jtag now transforms PA15, PB3 and PB4 to forbid their use without deactivating JTAG

Changed

• Fix hclk miscalculation

v0.3.0 - 2019-04-27

Added

• Added device-selected meta feature flag
• Restore and improve Serial DMA-based TX, RX and circular implementation
• Implement ADC example
• Implement ADC embedded_hal traits
• Implement ADC clock configuration
• Add feature for using STM32F101 chip
• Add gpio pins corresponding to LQFP-100 package
• Implement core::fmt::Write for serial::Tx
• Add methods stop, release and clear_update_interrupt_flag to Timer (clear_update_interrupt_flag does not apply to Timer<SYST>)
• Add timer interrupt example using RTFM
• Implement IndependentWatchdog for the IWDG peripheral
• Remove all PWM channel configurations except 'all the channels for default remapping' configurations
• Update PWM documentation: clarify custom selection of channels
• Add PWM example for custom selection of channels

Changed

• Breaking change Add additional configuration options to USART.
  • Baud rate now has to be set using configuration struct
• Now requires stm32f1 v0.7 (breaking change)
• enable PWM on stm32f100
• Fix gpio misconfiguration when using a timer in pwm input mode. Now the gpio has to be configured in floating input mode.

v0.2.1 - 2019-03-08

Added

• Add basic backup domain support
• Add support for real time clock
• Add patches for using STM32F100 chip (PWM disabled)

Changed

• Improve documentation

Fixed

• Use correct clock for serial baudrate computation

v0.2.0 - 2019-02-10

Added

• Add support for setting initial pin state
• Added ChangeLog

Changed

• Add information about device features to readme
• Allow read-/write-only transactions in write_read
• Bumped dependency versions (breaking change)

Fixed

• Fix link to docs.rs

[v0.1.1] - 2018-12-17

Added

• First tagged version